Remote access

Version 1.1.3 · plug-in API >=1.14 <2.0

PublishedHow to add it
On this page

Remote access: Install

Add Remote access from Starboard's Catalogue, where it is listed under Network. Starboard shows what it may do and tests it before anything is added. At the end, Remote access is active and its card is ready for your dashboard.

Before you begin

  • Starboard with plug-in API 1.14 or later. An older Starboard is offered an earlier version: read Updates.
  • Your Starboard password. Adding and removing a plug-in ask for it.
  • A 64-bit computer (amd64 or arm64). There is no build for 32-bit Arm, such as older Raspberry Pis, because Cloudflare does not make cloudflared for it.
  • A Tailscale account, or a Cloudflare account with a tunnel. Tailscale is recommended.

What it may do

Starboard lists these before you add it, each with its risk.

Permission Risk
Your apps and whether they answer (apps:read) Low
Reach other computers on your home network, and the internet (network:lan) Medium

What it runs:

  • main: reaches your home network and the internet, and this computer as host.docker.internal. It can use its own folder in Starboard's data (data/plugins/remote-access).

Like every plug-in, it runs read only, as a user that is not root, with no extra rights. Its image is pinned by digest, so what you approved is what runs.

Memory and processor

  • main: 128 MB of memory and 0.5 of a processor core at most.

Measured:

  • About 20 MB with nothing chosen, 22 to 32 MB with Tailscale waiting to sign in, and 20 to 30 MB with Cloudflare Tunnel, and 0.01 to 0.03% of a core at rest (13 November 2026).

Add it

  1. Go to Settings, then Plug-ins, then Catalogue.
  2. Under Network, find Remote access and select Install….
  3. A slide-out opens with what it can read, change and reach. Read it all.
  4. Enter your Starboard password and select Install Remote access. To stop, select Cancel: nothing is installed.
  5. Remote access's own tab opens under Settings, then Plug-ins. Select Activate. Its state changes to Active.

Add it by its address

On the Catalogue page, under Add one from elsewhere, paste this into The plug-in's manifest address, then select What it does and carry on from step 3:

https://raw.githubusercontent.com/TheMightyTRex/starboard-plugins/main/remote-access/starboard-plugin.json

Or run its installer, install.py in its folder, on any computer with Python, and give your Starboard's address.

Set it up with Tailscale

Your phone joins your own private network, a tailnet, and the shared apps answer there. Nothing is open to the internet.

  1. In your own Tailscale admin page, go to Settings, then Keys, and make an auth key. It starts with tskey-auth-.
  2. In Starboard, go to Settings, then Plug-ins, then Remote access.
  3. In Connect with, choose Tailscale (recommended).
  4. In Tailscale auth key, paste the key.
  5. Select Save.
  6. Wait for the card or Addresses away from home to say Connected.
  7. Install Tailscale on your phone and sign in to the same tailnet.
  8. Away from home, use the addresses in Addresses away from home, such as http://<its Tailscale address>:8095 for Starboard.

To sign in without a key, choose A sign-in link in Sign in with instead of steps 1, 4 and 5. Open the link that shows in Addresses away from home on any device, sign in to your own Tailscale account and approve this computer.

Set it up with Cloudflare Tunnel

You get a web address of your own, such as https://tv.example.org, through Cloudflare.

  1. In Cloudflare's dashboard, go to Networks, then Tunnels, and copy your tunnel's token. The whole command Cloudflare shows is fine too.
  2. In Cloudflare, add a public hostname for each app, pointing at http://localhost:8095 for Starboard, http://localhost:8096 for Jellyfin or http://localhost:13378 for Audiobookshelf, and nothing else.
  3. Protect Starboard's hostname with Cloudflare Access. Without it, Remote access stops the tunnel.
  4. In Starboard, go to Settings, then Plug-ins, then Remote access.
  5. In Connect with, choose Cloudflare Tunnel.
  6. In Cloudflare Tunnel token, paste the token.
  7. Select Save.
  8. Add Starboard's hostname to STARBOARD_ALLOWED_HOSTS in Starboard's settings file, so Starboard answers to it.
  9. Select Test remote access.

Cloudflare's terms limit how much video its free service carries, so use Tailscale to watch Jellyfin away from home.

Remove it

  1. Go to Settings, then Plug-ins, then Remote access.
  2. Under Remove, select Remove Remote access.
  3. Choose where its folder goes: Keep it with Starboard's data (in data/plugins/.removed) or Move it to the holding folder, listed in System, Clean up, where you can put it back or delete it for good.
  4. Enter your Starboard password and select Remove.

Its containers stop and go, and its API key stops working. Nothing is deleted.

To stop it for a while instead, select Deactivate on its tab: its settings and folder are kept.

Find out more

This page on GitHub, where the help is written.